Constant Curvature Array, Scalable 20° Vertical
| Frequency Response (-3dB)* | 52 Hz - 18 kHz |
| Frequency Range (-10 dB) | 45 Hz - 18 kHz |
| Horizontal Nominal Dispersion (-6dB) | 160° |
| Vertical Nominal Dispersion (-6 dB) | 20° |
| Max SPL @ 1W/1m (2.83v) | 131 dB SPL (140 dB SPL peak) |
| Dimensions (HxWxD) | 13.23” x 32.33” x 18.25” 336.14 x 821.21 x 463.68mm |
| Weight | 83lbs | 37.65kg |
14-gauge (2mm) perforated steel, powder- coated finish
Two 10” high-excursion ultra-low distortion drivers offer reduced power compression, providing efficient and accurate bass reproduction down to 52 Hz.
The CCA10 is a compact arrayable point source loudspeaker, designed for medium-sized venues to large distributed systems that need a flexible, scalable speaker solution.
Mounted horizontally with tight acoustic centers to minimize comb filtering, each CCA10 enclosure provides a fixed 20° vertical coverage and can be flown with additional enclosures in vertical arrays.
Featuring a coaxial compression driver that uses separate midrange and high-frequency polymer ring- shaped diaphragms, the compression driver delivers an extremely wide response from 420 Hz – 18,000 Hz.
Two 10” high-excursion ultra-low distortion drivers offer reduced power compression, providing efficient and accurate bass reproduction down
to 52 Hz.
| Frequency Response (-3dB)1 | 52 Hz – 18 kHz |
|---|---|
| Frequency Range (-10 dB)1 | 45 Hz – 18 kHz |
| Recommended High-Pass Filter | 48 Hz – w/ minimum 24 dB / Butterworth Filter |
| Horizontal Nominal Dispersion (-6 dB) | 160° |
| Vertical Nominal Dispersion (-6 dB) | 20° |
| Recommended Crossover Frequency | 420 Hz (acoustic, active, external DSP) |
| Long Term Power Handling (Low Freq.)2 | 600 W (2400 W peak) |
| Long Term Power Handling (High Freq.) 2 | 110 W (440 W peak) |
| Low Frequency Impedance | 4 ohms |
| High Frequency Impedance | 8 ohms |
| Pressure Sensitivity (Low Freq @ 1W/ 1m)3 | 101 dB |
| Pressure Sensitivity (High Freq. @ 1W/1m)3 | 111.4 dB |
| Max System SPL (@ 1W/1m) | 131 dB SPL (140 dB SPL peak) |
Contact the local distributor in your country; they can connect you with a local supplier.
No, download the EQ settings for the Blaze speakers from our website and upload them to a Blaze PowerZone Connect amplifier. The EQ settings also contain FIR filters, limiters, and crossovers for the CBL528.
Yes and No! The CBL523 can be used with a 2 or 4-pole Speakon connector. The CBL528 uses a 4-pole Speakon connector as this speaker is bi-amped. Use cable thicknesses according to the lengths of the cable. (A schematic can be found on our website: [insert link])
The CBL523 is a 4-ohm speaker, and therefore, one speaker can be connected to each output. Meaning, 4 speakers in total on a PowerZone Connect 504 amplifier. For more speakers connected in parallel, use the larger 2U amplifiers as they can handle down to 2-ohm loads.
In theory, all the PowerZone Connect amplifiers can be used. However, for the CBL523, the Connect 252/504 is a good match. To get full power, the bigger versions are recommended. For the CBL528, we recommend the Connect 3004, but lesser models can suffice if full power isn’t needed. Using the EQ settings from our website, the speakers are protected with limiters.
Subscribe now for exclusive updates on new product releases, firmware updates, case studies, and events.
